Looking for a commercial gate repair in Houston, TX? My Garage And Gates repairs dragging gates, failed motors, keypad and access control issues, storm damage, and worn hardware on iron, wood, aluminum, and chain-link commercial gates, with same-day service in most cases and a free estimate before any work begins.
A malfunctioning commercial gate is a security and access problem for your business, not just an inconvenience. Our crew works out of Cypress and handles repairs in-house across the greater Houston area, so most jobs get fixed the same day we show up.
Signs Your Commercial Gate Needs Repair
If you’re seeing any of these at your property, it’s time to call before the issue leaves your gate stuck open or closed:
- Dragging or misaligned gates. Often a worn wheel, loose chain, or bearing that's due for grease or replacement.
- Keypad or access code failures. Sometimes a simple code reset, other times rewiring or reprogramming.
- Damaged gate motors. Water intrusion, pests, and normal wear can all fail the transmitters and wiring inside.
- Worn hardware. Loose or rusty hinges, swing arms, and chains keep a gate from swinging or sliding smoothly.
- Storm or impact damage. High winds, falling branches, and vehicle collisions all take a toll on commercial gates.
- Unresponsive safety sensors. A gate that won't stop or reverse for an obstruction is a liability issue, not just a nuisance.
Why Houston Commercial Gates Need Repairs More Often
Commercial gates see more wear than residential ones, and Houston’s climate adds to it:
- Higher traffic volume. Multifamily, warehouse, and office properties cycle a gate dozens of times a day, so motors, hinges, and hardware wear out faster than on a residential driveway gate.
- Humidity and heavy rain. Metal gates and motor housings corrode faster in Houston's humidity, and electrical components are more prone to moisture damage than in drier climates.
- Expansive clay soil. Ground movement from Houston's "gumbo" clay can throw off gate alignment and track leveling, even on gates that were installed correctly.
- Storm and wind exposure. Gulf Coast storm season brings winds and debris that can bend tracks, crack panels, and knock automatic gates out of alignment.
How Much Does Commercial Gate Repair Cost in Houston, TX?
The cost depends on the gate type and whether the issue is mechanical, electrical, or structural; a keypad reset costs far less than a motor replacement or storm-damage panel repair. Because pricing varies by gate type, hardware, and site access, we don’t quote by phone. A technician assesses the gate in person and gives you an exact number, backed by a free, no-obligation estimate.
Commercial Gate Repair Services by Gate Type in Houston
We repair every commercial gate type and configuration we install. Here’s what each repair typically involves.
Automatic Gate Opener & Motor Repair
A gate that won’t open, won’t close, or moves unevenly usually points to the motor or transmitter rather than the gate itself. We troubleshoot and repair gate motors, transmitters, and wiring, and replace failed components so your automatic gate operates reliably again.
Access Control & Keypad Repair
Failed access codes, unresponsive keypads, and intermittent connectivity are common on commercial gates that see high daily traffic. We reset, rewire, or reprogram access hardware, and can integrate repairs with existing commercial access control systems.
Iron Gate Repair
Houston’s humidity speeds up rust on iron commercial gates, especially at weld points and anywhere the finish has chipped. We treat and repair rust spots before they spread, re-weld broken joints, and straighten bent panels or frames so the gate holds its structural strength.
Wood Gate Repair
Wood commercial gates take the most weather damage of any material we service: warped or split panels from heat and humidity swings, and hardware that works loose in high wind or under heavy daily use. We replace individual panels and posts rather than the entire gate wherever the frame remains solid.
Aluminum Gate Repair
Aluminum won’t rust the way iron or steel can, but it can dent, bend, or work loose at panel connections after an impact, and powder-coated finishes can chip and expose bare metal underneath. We straighten or replace bent panels, re-secure loose connections, and touch up finish damage before corrosion can start.
Chain Link Gate Repair
Commercial chain link gates usually fail at the top rail, the gate frame, or wherever the mesh has lost tension and started to sag under repeated daily use. We re-tension and re-secure the mesh, straighten or replace bent posts, and repair dragging or binding gates.
Sliding Gate Repair
Sliding commercial gates depend on a clean, level track; debris, ground movement, or a bent track are the most common causes of a gate that sticks or derails. We clear and re-level tracks, repair or replace rollers, and realign the gate so it slides smoothly again.
Swing Gate Repair
Swing gates put ongoing stress on hinges and swing arms, especially on high-traffic commercial properties. We repair or replace worn hinges and swing arms, and correct sagging or dragging gates caused by a settling post or foundation.
Structural & Storm Damage Repair
High winds, falling debris, and vehicle impacts can bend frames, crack panels, and knock a gate out of alignment. We assess structural damage on-site and repair or rebuild the affected sections so the gate is both secure and code-compliant again.
Planning something bigger than a repair? See New Gate Installation.
Commercial Gate Installation in Houston, TX
Beyond repairs, we also install new commercial gates for multifamily properties, offices, warehouses, and industrial sites, including custom iron and wood swing gates, rolling gates, and chain link gates, fabricated on-site and installed with same-day service in most cases.
Why Houston Businesses Choose Us for Commercial Gate Repair
- Same-day repairs on most jobs
- Free, no-obligation estimates
- In-house fabrication, not outsourced parts
- Licensed and insured technicians
- Local, family-owned and operated
- Automatic gate opener and access control repair included
- Transparent pricing before work begins
- Flexible scheduling around business hours
Areas We Serve
My Garage And Gates repairs commercial gates throughout Houston and everywhere within our 35-mile service radius out of Cypress. Find your city below:
- Houston, TX
- Baytown, TX
- Cleveland, TX
- Conroe, TX
- Fresno, TX
- Huffman, TX
- Katy, TX
- Friendswood, TX
- Montgomery, TX
- Cypress, TX
- Missouri City, TX
- Pearland, TX
- Humble, TX
- League City, TX
- La Porte, TX
- Kingwood, TX
- Webster, TX
- Magnolia, TX
- Rosenberg, TX
- Seabrook, TX
- Tomball, TX
- The Woodlands, TX
- Sugar Land, TX
- Spring, TX
- Richmond, TX
- Atascocita, TX
- Bellaire, TX
- New Caney, TX
- Pasadena, TX
- Deer Park, TX
- And more!
GOT QUESTIONS? WE'VE GOT ANSWERS FOR YOU
Frequently Asked Questions
What are the most common commercial gate repairs?
The most common repairs are dragging or misaligned gates, keypad and access code failures, damaged gate motors, worn hardware like hinges and rollers, storm or impact damage, and unresponsive safety sensors.
Do you repair commercial gates that another company installed?
Yes. We repair commercial gates regardless of who installed them, including gates from other installers or manufacturers, as long as we can source or fabricate compatible parts.
Do you offer maintenance plans to prevent future commercial gate repairs?
Yes. We offer preventive maintenance for commercial gates, including hardware inspections, lubrication, and access control checks, to catch small issues before they turn into a full repair.
Do you repair automatic gate openers and access control keypads?
Yes. We repair and reprogram gate motors, transmitters, keypads, and access codes, and troubleshoot connectivity issues on automatic commercial gates.
Can a damaged commercial gate be repaired instead of replaced?
In most cases, yes. We repair hinges, rollers, motors, panels, and hardware without replacing the full gate wherever the frame and structure are still sound.
What types of commercial gates do you repair?
Iron, wood, aluminum, composite, and chain-link commercial gates, in both swing and sliding configurations, along with their automatic openers and access control hardware.